Skip to content

Why Isn’t Your Heat Pump’s Auxiliary Heat Coming On?

  • by
  • HVAC

When a heat pump’s auxiliary heat fails to come on, the house can feel cold even though the system is running. The thermostat may show “Aux” or “Auxiliary Heat,” yet the air from the vents stays lukewarm, and the temperature slowly drops. This is a common winter complaint, and it usually points to a problem with the backup heat source, the controls that activate it, or the electrical circuit that powers it.

This guide explains how auxiliary heat works, why it might not engage, and which checks are safe for a homeowner. It covers thermostat configuration, breakers and fuses, sequencers and relays, heat strip failures, wiring faults, outdoor temperature lockouts, and defrost control problems. It also explains when to stop troubleshooting and call a qualified HVAC technician.

How Auxiliary Heat Works and Why It Matters

A heat pump is efficient, but its heating capacity drops as outdoor temperatures fall. At a certain point, the heat pump alone cannot keep up with the home’s heat loss. At that point, the auxiliary heat source activates to supplement the heat pump. In most all-electric systems, the auxiliary heat is a bank of electric resistance heat strips located in the air handler. In dual-fuel systems, the backup may be a gas or oil furnace.

Auxiliary heat is usually automatic. The thermostat or a control board decides when to energise the backup based on the difference between the setpoint and the room temperature, the outdoor temperature, or a signal from the defrost board. Emergency heat is different: it is a manual setting that locks out the heat pump and relies entirely on the backup source. Confusing the two settings is a common reason homeowners think the auxiliary heat is not working.

When auxiliary heat engages, you may notice a warmer feel at the vents, a change in blower speed, or a faint humming from the air handler. On a cold morning, the system may run the heat pump and the auxiliary heat together. If the auxiliary heat never engages, the heat pump may run continuously without satisfying the thermostat, and the house may feel cool and damp.

Start With the Thermostat Settings and Configuration

Before investigating the equipment, confirm that the thermostat is asking for auxiliary heat. Set the mode to Heat, not Emergency Heat, and raise the setpoint several degrees above the current room temperature. A large setpoint jump, often more than a few degrees, can trigger auxiliary heat on many thermostats. Wait a few minutes and observe whether the “Aux” indicator appears and whether the air warms.

heat pump auxiliary heat not coming on

Check the thermostat’s equipment configuration. A thermostat installed for a conventional furnace rather than a heat pump may never energise the auxiliary heat terminal. The settings should indicate a heat pump with auxiliary or backup heat, and the auxiliary wire, often labelled AUX or W2, should be detected. If the thermostat does not recognise the auxiliary wire, it cannot call for backup heat no matter what the display shows.

Review any energy-saving or eco settings. Some thermostats intentionally disable auxiliary heat to reduce energy use, or they lock out the backup above a certain outdoor temperature. A schedule or geofencing feature may also be holding the system in an efficiency mode. If the thermostat has an auxiliary lockout or a balance point setting, confirm that it is configured for your climate and equipment rather than left at a default that prevents the backup from running.

Cause 1: A Tripped Breaker or Blown Fuse

Electric heat strips draw a large amount of current, and they often run on a separate 240-volt circuit from the heat pump compressor. Look in the main electrical panel for a double-pole breaker labelled “Air Handler,” “Heat Strips,” “Aux Heat,” or “AHU.” If the breaker is tripped, reset it once and observe. If it trips again within a short period, stop and call a technician, because a repeated trip can indicate a shorted element or a wiring fault.

Some air handlers also have a smaller breaker or a fuse block mounted on or inside the unit. Check those protective devices if they are accessible and the manufacturer’s instructions permit it. A blown fuse or an open breaker cuts power to the heat strips even though the thermostat and the heat pump continue to operate. The result is a system that runs but never delivers the expected warmth.

A high-limit safety switch may also have opened. Heat strips include a high-temperature limit that cuts power if airflow is restricted or the strips overheat. If the limit has tripped, it may reset automatically when the unit cools, or it may require manual reset depending on the design. Repeated limit trips point to an airflow problem that needs correction rather than repeated resets.

Cause 2: A Failed Sequencer or Relay

The sequencer is a relay-like device that staggers the heat strips so they do not all energise at once. Staging prevents a sudden current surge that could trip the breaker. When the thermostat calls for auxiliary heat, it sends a low-voltage signal to the sequencer, which closes contacts and powers the heating elements. A failed sequencer can prevent the strips from energising even when the thermostat is calling correctly.

Relays and contactors perform a similar switching role in some air handlers. A pitted or stuck contactor may not close, or it may close only intermittently. A sequencer that has failed open will leave the strips unpowered, while a sequencer that has failed closed can leave the strips running continuously or cause a high-limit trip. These components are tested with a multimeter by checking for control voltage and continuity across the contacts.

Testing a sequencer or relay requires access to the air handler’s electrical compartment, which contains high voltage. Do not open that compartment unless you are trained and the power is isolated at the breaker. A technician can confirm whether the control signal is reaching the sequencer and whether the sequencer is passing power to the elements. If the sequencer is faulty, replacement is usually straightforward for a qualified technician.

Cause 3: Failed Heat Strips or a Broken Element

Heat strips are resistive elements that degrade over time. An element can break, short, or develop a hot spot that trips the high-limit switch. If one strip in a bank fails, the system may still produce some heat but not enough to satisfy the thermostat. If all strips fail, the auxiliary heat is effectively absent, and the heat pump runs alone.

A failed element may show visible signs such as a burnt terminal, a discoloured wire, or a broken coil. However, not all failures are visible. A technician uses a multimeter to check continuity and resistance across each element and to confirm that the sequencer is supplying power. Replacing a heat strip requires matching the correct part number, wattage, and physical size, and it should be done with the power isolated.

Do not attempt to repair a heat strip by rewiring or bypassing a broken section. Elements are not user-repairable, and a modified element can overheat or create a short circuit. If a strip has failed, replacement is the correct repair. If the failure has damaged the surrounding wiring or the sequencer, those components should be replaced as well.

Cause 4: Thermostat Wiring and Control Signal Problems

The auxiliary heat depends on a low-voltage control signal from the thermostat to the air handler. A loose, damaged, or miswired conductor can prevent that signal from arriving. The auxiliary wire is often white and connects to the AUX or W2 terminal at the thermostat and to the corresponding terminal at the air handler or zone controller. A wire that is not fully seated can cause intermittent operation.

Zone control systems add another layer of complexity. A zone controller may need to be configured for heat pump operation with auxiliary heat, and a missing jumper between terminals can prevent the backup from activating. If the system has multiple zones, confirm that the zone calling for heat is also authorised to use auxiliary heat. A zone controller that is set for a conventional system may never energise the auxiliary terminal.

Thermostat wiring should be inspected with the power off at the air handler and the thermostat. Do not move wires to different terminals in an attempt to force the auxiliary heat on, because an incorrect connection can damage the control board or create a safety hazard. If the wiring appears damaged or the terminal labels are unclear, a technician can trace the circuit and confirm the correct configuration.

Cause 5: Outdoor Temperature Lockout, Balance Point, or Defrost Control

Many heat pump thermostats use an outdoor temperature sensor or a weather data feed to decide when auxiliary heat is allowed. If the balance point or lockout is set incorrectly, the auxiliary heat may be disabled when it is actually needed, or it may be locked out entirely. A balance point that is too low can leave the heat pump struggling alone in cold weather, while a lockout that is too aggressive can prevent the backup from running at all.

The defrost control board also plays a role. During defrost, the board should energise the auxiliary heat to prevent cold air from reaching the rooms. If the defrost board or its relay fails, the auxiliary heat may not engage during defrost, and the house may feel a cool draft every time the system defrosts. A heat pump that seems stuck in defrost mode can also cause the auxiliary heat to run improperly or not at all, and a guide to a heat pump stuck in defrost mode explains the related symptoms and checks.

heat pump auxiliary heat not coming on

Outdoor thermostats and lockout settings are installation-specific. Do not copy a setting from another home or a generic online guide. The correct balance point depends on the heat pump’s capacity, the home’s insulation, the local climate, and the cost of electricity. A qualified technician can set the balance point and verify that the auxiliary heat is allowed to run when the outdoor temperature falls below it.

Safe Diagnostic Steps for Homeowners

Before calling a technician, perform the checks that do not require opening the air handler or touching high-voltage wiring. These steps can confirm whether the thermostat is requesting auxiliary heat and whether power is reaching the equipment. Keep the thermostat in normal Heat mode and avoid repeated large setpoint changes while you observe.

  1. Confirm the thermostat is in Heat mode and set several degrees above room temperature.
  2. Check whether the “Aux” or “Auxiliary Heat” indicator appears on the display.
  3. Verify that the thermostat is configured for a heat pump with auxiliary heat.
  4. Look for a tripped double-pole breaker labelled Air Handler, Heat Strips, or AHU.
  5. Check the air filter and replace it if it is dirty or overdue.
  6. Inspect the thermostat wiring for loose or disconnected conductors, with power off.
  7. Listen for a relay click or a change in blower sound when auxiliary heat should engage.
  8. Record any error code or fault indicator on the thermostat or air handler.

Do not open the air handler’s electrical compartment, test a sequencer with a multimeter, or replace a heat strip unless you are trained and the power is isolated. These components operate at high voltage and high current. If you smell burning, see scorch marks, or the breaker trips repeatedly, stop and call a qualified technician. If you smell gas in a dual-fuel system, leave the area and call the gas utility from outside.

Comparison Table: Auxiliary Heat Symptoms and Likely Causes

Symptom Likely cause Safe first check
Thermostat shows Aux but air stays cool Tripped breaker, failed sequencer, or open limit Check the air handler breaker; reset once; call if it trips again
No Aux indicator, house stays cool Thermostat configuration or balance point lockout Verify heat pump with aux settings; review lockout temperature
Aux engages intermittently Loose thermostat wire or failing sequencer Inspect accessible wiring with power off; call for sequencer test
Aux runs but heat is weak One or more failed heat strips Call a technician to test element continuity and power
Aux does not run during defrost Defrost board or relay fault Record defrost behaviour; call for control board diagnosis
Breaker trips when Aux engages Shorted element or wiring fault Stop resetting the breaker; call a technician

When to Call a Technician

Call a qualified HVAC technician if the auxiliary heat still does not engage after the thermostat and breaker checks. A technician can measure the control voltage at the sequencer, test the heat strips for continuity, verify the thermostat configuration, and check the balance point and defrost board. These tests require access to high-voltage components and a multimeter, and they are not safe for an untrained homeowner.

Call immediately if the breaker trips repeatedly, if you smell burning or see scorch marks, or if the air handler makes a loud humming or buzzing sound. These signs can indicate a shorted element, a failing sequencer, or a wiring fault that could lead to a fire. If the system is a dual-fuel installation with a gas furnace, a gas smell is an emergency: leave the building and call the gas utility from outside.

Other winter appliance problems can compete for attention during a cold snap. A guide to too much heat from an oven vent explains a separate kitchen concern, and an article on the best light bulb for pump house heating covers a cold-weather outbuilding issue. Addressing each system methodically helps you avoid overlooking a safety problem while managing comfort.

Preventing Repeat Auxiliary Heat Failures

Schedule annual heat pump maintenance before the heating season. A technician can test the heat strips, inspect the sequencer and wiring, verify the thermostat configuration, and check the balance point and defrost operation. Regular service catches a failing sequencer or a degraded element before it leaves the house cold during the first cold snap.

Keep the air filter clean and the return grilles open. Restricted airflow can cause the heat strips to overheat and trip the high-limit switch, which prevents the auxiliary heat from running. A clean filter also helps the heat pump operate efficiently and reduces the load on the backup heat. Replace the filter according to the manufacturer’s guidance, and check it more often in homes with pets or dusty conditions.

Do not change balance point or lockout settings without professional advice. These settings are matched to the equipment and the home, and an incorrect setting can disable the auxiliary heat when it is needed or cause it to run unnecessarily. If you have a smart thermostat, review the equipment configuration after any software update or thermostat replacement to confirm that the auxiliary heat is still recognised and allowed to run.

FAQ

Why does my thermostat show Aux but the air is not warm?

The Aux indicator means the thermostat is requesting backup heat, not that the backup is actually running. A tripped breaker, a failed sequencer, an open high-limit switch, or a broken heat strip can prevent the elements from energising. Check the air handler breaker and the air filter first, then call a technician if the air stays cool.

Can I use Emergency Heat until the auxiliary heat is repaired?

Emergency Heat is a manual setting that locks out the heat pump and relies entirely on the backup source. It can provide temporary warmth, but it uses more energy and does not fix the underlying fault. Use it only as a short-term measure while you arrange service, and do not leave it on as a permanent solution.

Why does the auxiliary heat run sometimes but not on cold mornings?

Intermittent operation often points to a loose thermostat wire, a failing sequencer, or a balance point setting that is borderline. A sequencer that is beginning to fail may close on some calls but not others. A technician can test the control signal and the sequencer to confirm the fault.

Conclusion

A heat pump auxiliary heat system that does not come on is usually caused by a thermostat configuration problem, a tripped breaker or open limit, a failed sequencer or relay, a broken heat strip, a wiring fault, or an outdoor lockout and defrost control issue. Confirming the thermostat mode and settings, checking the air handler breaker, and replacing a dirty filter are safe first steps that can resolve simple causes.

Do not open the air handler’s electrical compartment, test high-voltage components, or replace heat strips unless you are trained and the power is isolated. If the auxiliary heat still does not engage, or if the breaker trips repeatedly or you smell burning, call a qualified technician. A technician can test the sequencer, elements, wiring, and balance point and confirm the correct repair.

Regular maintenance and correct thermostat settings reduce the chance of a repeat failure and help the system deliver reliable warmth through the coldest weather.

Leave a Reply

Your email address will not be published. Required fields are marked *